ABL Light Pipes

[ka1]

Originally Posted by sjmautoprod

We supply heat-shrink tubing to attach the LEDs to the pipes for the dash.

There is a complete dash kit (no thinking required), and, piece-parts.

Is there a discount for Camaro5 members. If so, I need a tuned flex light pipe and a RGB ABL LED. Can you PM a quote for this?

Thanks!

[sjmautoprod]

Our pipes are 5mm, BUT, the shifter seems to best be done with 3mm. I tried getting my supplier to do the 3, but, they could not do it the way we wanted it. :(

The 5mm x 1000mm flex pipe is $22, and, a wired, RGB LED would be $15 (maybe less, depending).

I assume that you already have an RGB controller?

[ka1]

Originally Posted by sjmautoprod

Our pipes are 5mm, BUT, the shifter seems to best be done with 3mm. I tried getting my supplier to do the 3, but, they could not do it the way we wanted it. :(

The 5mm x 1000mm flex pipe is $22, and, a wired, RGB LED would be $15 (maybe less, depending).

I assume that you already have an RGB controller?

I do

[sjmautoprod]

If you want to try the 5mm, just let me know the wire length that you would need to get to your controller.

[vgradio]

Originally Posted by sjmautoprod

Finally, some video of an RGB dash/door install...

That's really great, I like to do the same.

Could you please tell me what material would be required and how to connect everything together, especially how to use the car dimming?

Thanks,

[sjmautoprod]

That can be done with our NightOwl Dash and Door ABL kit, with the addition of footwell lighting.

For the footwells, you could use a MiniSL (supports two, independent devices), or, an SL (four devices), along with two LED strips. I should put some kits together for this.

[Quickstir]

What would I need to put ABL on my door panels? I bought the dash kit a while back. I don't currently have any ABL on my door panels.

[scdude37]

Glad this came up, I will be needing this since I just got my pieces hydro dipped and wanna show them off at night

[sjmautoprod]

Originally Posted by Quickstir

What would I need to put ABL on my door panels? I bought the dash kit a while back. I don't currently have any ABL on my door panels.

First, you need the clear panels that are painted on the back side. From the outside, you should be able to see a line/strip towards the top.

After that, pipes, clips, screws/washers, and, t-taps.

We need to add this specific config to our site as we only have it for the NightOwl version now.

[Quickstir]

Originally Posted by sjmautoprod

First, you need the clear panels that are painted on the back side. From the outside, you should be able to see a line/strip towards the top.

After that, pipes, clips, screws/washers, and, t-taps.

We need to add this specific config to our site as we only have it for the NightOwl version now.

Yeah I already have clear panels with top part lightly sanded. Was thinking of sanding bottom as well. Kind of thinking of lighting up the entire door panel edge. When I swapped them out i noticed a small plug that wasn't connected to anything. I think its the ABL thing but didn't check if power was going to it. By the way, I have 2012 camaro.

[sjmautoprod]

We have parts to do the whole panel, if you want.

[sjmautoprod]

Ah, we already had this up...

http://sjmautoprod.com/Interior/Door...es-Bottom.html

[sjmautoprod]

Bump!

[not a dodge]

went on your site, un clear what I am getting, I have the LED for the end but need the pipe for the dash. So what do I order?