05-29-2011, 08:41 PM | #1 |
Installing Hurst Billet short throw tomorrow
My Hurst shifter came in yesterday! Im going to install it tomorrow. Im not that great at workin on cars but I have my pops help thank god..LOL. ANy tips or suggestions on the install? Thanks
|
|
05-29-2011, 08:53 PM | #2 |
BL1ZZRD
Drives: '16 Camaro 2SS, '20 Equinox Redline Join Date: Jul 2009
Location: Buffalo, NY
Posts: 7,840
|
Great! I have the same thing! The only thing I can say on the install is make sure you are carefull not to drop the little c clamps on the pin underneath! If you drop them they will probably land on the heat sheild and it'll be tough to find. Other than that piece of cake! Good luck!
|
05-29-2011, 08:57 PM | #3 |
SoCal Mayhem
Drives: 2010 Camaro 1SS/RS Join Date: Aug 2008
Location: Foothill Ranch, CA
Posts: 5,488
|
Give this a watch
__________________
|
05-29-2011, 09:04 PM | #4 |
Drives: 2010 Camaro LS M6 Inferno Orange Join Date: May 2010
Location: Lebanon, OH
Posts: 1,672
|
I just installed my Barton yesterday. A friend has a lift so that made it a ton easier than trying it on jack stands. It was 90 minutes from pulling onto the lift and pulling out of his driveway.
One of the c-clips did pop off and land on the heat shield. We just removed the front two nuts on the shield and pulled down and the c-clip fell out.
__________________
Gordy
Injen CAI / Solo Mach-X LLT / Solo High-flow res-cats / Barton short shifter / RX Catch Can / RPI Gills / 35% tint / LED Footwell Lighting Front & Rear / Pedders Street 1 / Pedders steering rack bushing / SS struts / Pfadt drop springs / VMax Ported Throttle Body / Spohn Toe Rods / Spohn Trailing Arms / Trifecta Tune / MACE 25mm Intake Spacers Find me on Facebook: http://www.facebook.com/gahammerle |
05-29-2011, 09:15 PM | #5 |
Drives: 2010 Camaro SS/RS 6spd Join Date: Sep 2009
Location: Jefferson, Ga
Posts: 4,399
|
I dont have the hurst, but I did find that removing the tunnel brace and the heat sheild gave you more room to mess around with it! And also make SURE you put the rubber boot on correctly, and make sure it is secure. Mine fell off and I had to get a new one because it ripped.
__________________
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Hurst short throw | LSU/LS3 | Transmission / Driveline | 9 | 01-14-2011 01:53 PM |
The New and Improved Hurst Shifter | alfie43 | V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) | 29 | 08-11-2010 10:47 PM |
Can the hurst short throw void warranty ? | Ex-stang | Camaro Issues / Problems | Warranty Discussions | TSB and Recalls | 3 | 04-07-2010 07:52 AM |
Short Throw Hurst Shifter Not Available | Matster | 5th Gen Camaro SS LS LT General Discussions | 51 | 11-09-2009 10:03 AM |
hurst short throw | chelsea1 | 5th Gen Camaro SS LS LT General Discussions | 4 | 03-12-2009 09:23 PM |