You are browsing camaro5 
 |
|
02-15-2010, 03:52 PM
|
#1 |
   
Drives: 2000 Silverado Join Date: Apr 2009
Location: Southern WI
Posts: 1,240
|
Corsa installation question......
so i got the installation done 2day.....cant drive it yet (winter here), but i started it up.
Corsa says 45lb of torque on the clamps (which isn't enuff). i went tight enuff to secure the 2 pipes but when running the car, i'm getting water dripping outta the clamped joints. my question is.........is that normal? i know the small amount of smoke is, and the smell is, but the exaust moisture?
__________________
IOM 2SSRS LS3 R6P - VIN 7553 Delivered 5/22/2009 Kooks, Corsa and Roto-Fab - SOLD 9/2010
VR 2SSRS LS3 - Borla, SLP CAI |
|
|
|
02-15-2010, 03:55 PM
|
#2 | |
 
Drives: BLUE CAMARO ZL1 1LE M6 Join Date: Jun 2009
Location: ON THE DYNO WATERBURY CT.
Posts: 15,416
|
Quote:
That is perfectly normal and tighter is not better, you can distort the pipes and make things worse. Don't be afraid to retorque after a few heat cycles, but do not exceed 45 ft. lb torque. Ted.
__________________
www.jannettyracing.com
Celebrating 39 years Performance parts, Installation, Fabrication, Dyno tuning, Remote custom tuning, and alignments. 203-753-7223 Waterbury CT. 06705 email tedj@jannettyracing.com |
|
|
|
|
|
02-15-2010, 04:14 PM
|
#3 |
|
Drives: 2000 Silverado Join Date: Apr 2009
Location: Southern WI
Posts: 1,240
|
so the moisture will stop dripping after a little driving this spring?
__________________
IOM 2SSRS LS3 R6P - VIN 7553 Delivered 5/22/2009 Kooks, Corsa and Roto-Fab - SOLD 9/2010
VR 2SSRS LS3 - Borla, SLP CAI |
|
|
|
|
02-15-2010, 04:17 PM
|
#4 | |
|
Drives: BLUE CAMARO ZL1 1LE M6 Join Date: Jun 2009
Location: ON THE DYNO WATERBURY CT.
Posts: 15,416
|
Quote:
Normal Ted.
__________________
www.jannettyracing.com
Celebrating 39 years Performance parts, Installation, Fabrication, Dyno tuning, Remote custom tuning, and alignments. 203-753-7223 Waterbury CT. 06705 email tedj@jannettyracing.com |
|
|
|
|
|
02-15-2010, 04:18 PM
|
#5 |
|
Drives: 2000 Silverado Join Date: Apr 2009
Location: Southern WI
Posts: 1,240
|
thanks Ted........u rock!
__________________
IOM 2SSRS LS3 R6P - VIN 7553 Delivered 5/22/2009 Kooks, Corsa and Roto-Fab - SOLD 9/2010
VR 2SSRS LS3 - Borla, SLP CAI |
|
|
|
|
02-15-2010, 04:27 PM
|
#6 |
|
Drives: 2000 Silverado Join Date: Apr 2009
Location: Southern WI
Posts: 1,240
|
u were right Ted, the Kooks installation was super simple too. the Roto-Fab was simple as well.
so i'm also noticing a ruff idle.........about 500rpms as it warm up. no codes yet. i haven't tuned it yet either. any ideas about the ruff idle? also, i was gonna call ya tomorrow about HPTuners Ted. is there a best time to reach ya?
__________________
IOM 2SSRS LS3 R6P - VIN 7553 Delivered 5/22/2009 Kooks, Corsa and Roto-Fab - SOLD 9/2010
VR 2SSRS LS3 - Borla, SLP CAI |
|
|
|
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Question about spoiler installation... | marley. | Cosmetics and Lighting Modification Discussions | 8 | 12-18-2009 11:27 AM |
| Corsa Exhaust System Christmas Special and free shipping | GmPartsDirect.com | V8 Bolt-Ons & Tunes | 9 | 12-10-2009 07:55 AM |
| 2010 Camaro MagnaCharger + INSTALLATION | hoekdup | Forced Induction | 4 | 11-28-2009 05:50 AM |
| 2010 Camaro MagnaCharger + INSTALLATION | hoekdup | V8 Bolt-Ons & Tunes | 6 | 11-27-2009 05:23 PM |
| Corsa Exhaust | tones2SS | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 3 | 05-14-2009 03:04 PM |
