New SLP Style Splitter Install (cheap)

[shibbs]

Originally Posted by Deltasig

Alright, so I installed the splitter. Just one concern though, I left out the rubber piece (air diffuser) from under the front bumper because I thought the splitter was going to get in the way where it curved at both ends. But now looking at other photos it seems most people left theirs on. Did the rubber piece underneath the front bumper fit nice and flush under the splitter for you guys where it curved at both ends? See picture with red arrow below:

I left mine on - Just had to trim a little bit off it, and then the ends went on the bottom of the splitter.

I just followed SLP's instructions.

[justjoshin]

Originally Posted by shibbs

I left mine on - Just had to trim a little bit off it, and then the ends went on the bottom of the splitter.

I just followed SLP's instructions.

+1

[digdeep0169]

looks can be deceiving but i know this doesn't actually lower the car in front, but it does look like it extends out forward thus reducing your approach to steeper driveways... do any of you run into this?

[Sapper12b]

Originally Posted by justjoshin

I noticed the T4 used the push-type retainers along the front. Not a big fan of those.

After having to pay $400 to learn that lesson, I totally agree with you. Next splitter is going to be bolted on permanently .

[moosey3000]

I just installed mine this weekend.

[Sapper12b]

Originally Posted by moosey3000

I just installed mine this weekend.

where did you get yours, possible link ?

[MillerTime]

Originally Posted by Sapper12b

where did you get yours, possible link ?

EBay. Just search SLP style splitter. With some minimal sanding they turn out pretty nice.

[2011ss/rs]

I have the SPL splitter from RPI. The bolts are a pain in the ass if you are installing it alone. After removing it for a repaint we reinstalled the splitter* using Balkamp #10-32 part number 665-2834 screw sets for under $20.00.No more cut up forearms from the install, no two way tape and* the hold is real strong. Drill the hole push the threaded rubber through screw it tight repeat 7 more times.

[OmniCamaro]

Originally Posted by digdeep0169

looks can be deceiving but i know this doesn't actually lower the car in front, but it does look like it extends out forward thus reducing your approach to steeper driveways... do any of you run into this?

I'm at stock ride height at the moment and I haven't scraped it once. I am careful though. I back in, angled approach going forward, and slow down for speed bumps. Like a snails pace slow.

[newagemuscle]

Originally Posted by IcedBee

I just received mine yesterday and I must say... it's quite disappointing. The top looks really good but the underneath looks like a kid played with plastic

That's why i will just sell it and order a SLP or ACS T4 for 100 Bucks more but with much better quality.

Wow... that looks like crap. The top looks just like my SLP. This is the first time I saw the underside. Some things are worth the extra money. Here is the underside of my SLP for comparison.

[moosey3000]

Originally Posted by Sapper12b

where did you get yours, possible link ?

Here you go:
http://www.ebay.com/itm/10-13-CHEVY-...749a9b&vxp=mtr

[camarohead]

Ok after much review, going with this cheap slp style splitter..about to order..can someone post the link to the one I need to get? Preferably the cheapest one with the hardware..one with a trusted seller...thx

[camarohead]

I see one for $145 + shipping on amazon...is that a good one?

[justjoshin]

yep, looks like the best deal right now.

http://www.amazon.com/Camero-Urethan...s=slp+splitter